Guides
How to draw a floor plan from a hand sketch with measurements
Short answer: read the whole sketch first, then check that each row of room sizes plus wall thicknesses adds up to the outside length (for example 3.85 + 3.65 m of rooms, plus 0.10 m inner wall and two 0.30 m outer walls, is 8.20 m). Draw the outer walls first, then the long inner walls, then rooms, openings, stairs and fixtures. Work out missing sizes by subtraction where you can, mark estimates, and send the client one message with all open questions when a difference is larger than rounding.
Most real estate plans start as a sketch: a measurer or photographer walks through the home with a laser meter and writes sizes on paper or a tablet. The sketch is rough on purpose. Your job is to turn it into a plan that is correct to the centimetre where the sizes are known and honest where they are not. This is the method that keeps revision rounds to a minimum.
Step 1: read the whole sketch before you draw
Do not start drawing at the front door. First get the full picture:
- Floors. How many are there, and which page is which? Look for labels such as ground floor, first floor or attic; on Dutch sketches BG, 1e verd. and zolder.
- Orientation. Find the front door and the stairs. The stairs sit in the same place on each floor and tie the pages together.
- Units. 385 is probably centimetres, 3.85 or 3,85 metres, and 3850 millimetres. Measurers are not always consistent within one sketch.
- What each number measures. Inside room sizes, overall outside lengths, wall thicknesses, window widths, ceiling heights. A number written across a room is usually an inside size; a number outside the outline is often an overall length.
- Symbols and abbreviations. Door swings, windows, mk for the meter cupboard or cv for the boiler on Dutch sketches. See floor plan symbols and abbreviations.
- Heights. For attics, look for the place where the sloping roof is 1.5 m and 2.0 m high. Dutch clients expect those lines on the plan.
Ask for the listing photos too, if the client has them. A photo settles most questions about which way a door opens or where a window sits.
Step 2: check that the measurements add up
This is the step that separates a reliable drafter from a fast one. Along every wall line of the house, the inside sizes plus the wall thicknesses must equal the outside length.
Example: the front of a house is 8.20 m outside. Behind it are a living room of 3.85 m and a hall of 3.65 m, with one inner wall of 0.10 m and outer walls of 0.30 m. Check: 3.85 + 3.65 + 0.10 + 0.30 + 0.30 = 8.20 m. It adds up.
If the sketch gives no outside lengths, compare floors instead: the ground floor and the floor above usually have the same outer outline. Rows of rooms side by side should also reach the same total.
Example: on the first floor, two bedrooms of 3.40 m and 2.90 m and a bathroom of 1.20 m sit in a row. With two inner walls of 0.10 m, that is 3.40 + 2.90 + 1.20 + 0.20 = 7.70 m inside. Downstairs the same front measured 7.60 m inside. A 10 cm difference: one size is off, or one inner wall is thicker than you assumed.
Is a room square in the corners? If the measurer wrote a diagonal, check it with Pythagoras: a room of 4.00 × 3.00 m has a diagonal of √(16 + 9) = 5.00 m. A diagonal of 5.10 m means the room is not rectangular, or one size is wrong.
Decide with each client what difference is acceptable. A few centimetres from rounding is normal on a sketch. Larger differences need an answer before you deliver.
Want to try it? Open the sample home, no account needed.Want to try it on your computer? Email yourself the link.
Step 3: draw the walls in the right order
- Draw the outer walls of the ground floor at their real thickness, on the inside sizes the sketch gives. This fixes the outline.
- Draw the long inner walls that run through the house, such as the wall between the front and back rooms or along the hall.
- Fill in the rooms between them, working from one outer wall to the other so any difference ends up in one place you can see.
- Place the doors and windows, with the swing direction and hinge side from the sketch or photos.
- Draw the stairs, with an arrow pointing up.
- Add fixtures: kitchen, toilet, bath, shower, washbasin, boiler, meter cupboard.
- Draw the next floor on top of the one below, starting from the stairs and the outer walls.
- Name the rooms, add dimension lines and room areas, and apply the client's style.
Working outside-in matters. If you start at the front door and add rooms one by one, small errors pile up, and by the back wall you are 15 cm out with no idea where it came from.
Step 4: handle missing measurements
Every sketch has gaps. Handle them in this order:
- Subtract. If you know the outside length and all rooms but one, the missing one is the difference. This is exact and needs no question.
- Use the other floor. An outer wall or a stair measured on one floor is usually the same on the other.
- Use the photos. Count floor tiles of a known size, or compare with a door or a kitchen worktop, which is usually about 60 cm deep. Good enough for a cupboard, not for a bedroom.
- Mark what you estimated. Keep a note of every size you derived or estimated, and tell the client. Never deliver a guessed room size as if it were measured.
When to ask the client
Ask when:
- a whole room has no size and cannot be derived;
- sizes do not add up by more than the difference you agreed on;
- it is unclear which number belongs to which wall;
- attic heights are missing on a Dutch home;
- a room is on the sketch but not in the photos, or the other way round.
Send one message with all questions, numbered, with a screenshot of the sketch where you marked each point. A client who measures for a living can answer five clear questions in two minutes. Five separate messages over a day cost you both time. If the deadline is close, deliver with the open points clearly marked and agree to send a corrected version.
Common mistakes
- Drawing walls as thin lines and putting the room sizes on the centre of the wall. Every room ends up too large.
- Using outside sizes as room sizes.
- Forgetting that the stairwell on the upper floor is a hole, not floor area.
- Copying a number that does not fit instead of asking.
- Rounding everything to 5 or 10 cm "to make it neat".
Our floor plan checklist has 12 checks to run before you deliver, and how to calculate square meters covers area rules per country.
How Dinoplan helps
In Dinoplan you can put a scan, photo or sketch in the background, set the scale with one known measurement and draw over it. From a photo or iPad sketch of a survey, Dinoplan first finds the walls and windows; you then type the measurements written next to them. This happens in your browser, so the sketch is not uploaded anywhere. You can also type a whole room, such as 385×365, and it appears with those inside dimensions. On the Agency plan you can add notes on the plan, for example what still needs measuring; they never go into an export. Always check the result against the sketch: the wall detection gives you a start, the sizes are still yours to verify. Dinoplan also reads an architect's vector PDF; see floor plan from a PDF with AI. More on the features page and pricing.
Frequently asked questions
How do I turn a hand drawn sketch into a floor plan?
Read the whole sketch, check that the sizes add up per wall line, draw the outer walls first, then inner walls, rooms, doors, windows, stairs and fixtures. Ask about anything that does not add up.
What do I do if a measurement is missing?
Work it out by subtraction from an outside length if you can. Otherwise check the other floor or the photos, mark it as estimated, and ask the client if it matters for a room size.
How much difference is acceptable between sizes on a sketch?
A few centimetres from rounding is normal. Agree a limit with each client, and ask about anything larger before you deliver.
Should I draw walls on the inside or the centre line?
On a sales plan, draw walls at their real thickness with the room sizes on the inside faces. Sizes on the centre line make every room too large.
Can software read a hand sketch automatically?
Some tools detect walls in a photographed sketch. In Dinoplan this gives you the walls and windows to start from, and you type the measurements. Always check the result against the sketch.
Why do my room sizes not add up to the outside length?
Usually because the wall thicknesses are missing from the sum, or one inner wall is thicker than assumed. Add every wall, then look for the single size that is off.